|
分支:ngap-wf-1120-srb-gtp
环境:Ubuntu 18.04.3 LTS X86_64
命令:
GNB侧:./targets/bin/nr-softmodem.Rel15 -E -O ./gnb.conf --do-ra
GNB配置:
absoluteFrequencySSB = 500208;
dl_frequencyBand = 41;
dl_absoluteFrequencyPointA = 499200;
dl_offstToCarrier = 0;
dl_subcarrierSpacing = 1;
dl_carrierBandwidth = 106;
initialDLBWPlocationAndBandwidth = 13475;
initialDLBWPsubcarrierSpacing = 1;
initialDLBWPcontrolResourceSetZero = 12;
initialDLBWPsearchSpaceZero = 0;
ul_frequencyBand = 41;
ul_offstToCarrier = 0;
ul_subcarrierSpacing = 1;
ul_carrierBandwidth = 106;
initialULBWPlocationAndBandwidth = 13475;
initialULBWPsubcarrierSpacing = 1;
nrUE侧: ./targets/bin/nr-uesoftmodem.Rel15 --numerology 1 -r 106 -C 2501040000 --ue-scan-carrier --ue-txgain 70 --ue-rxgain 90 -E --usrp-args type=b200 --do-ra -T -U 1
运行结果:
GNB侧:
[HW] RX Gain 0 114.000000 (49.800000) => 64.200000 (max 76.000000)
[HW] USRP TX_GAIN:89.75 gain_range:89.75 tx_gain:0.00
...
TYPE <CTRL-C> TO TERMINATE
Entering ITTI signals handler
[PHY] ru_thread_prach() RACH waiting for RU to be configured
[PHY] ru_thread_prach() RU configured - RACH processing thread running
[PHY] RU 0 rf device ready
[PHY] RU 0 no asynch_south interface
ru_thread_tx ready
sleep...
sleep...
sleep...
sleep...
sleep...
sleep...
sleep...
sleep...
sleep...
[PHY] gNB 0 frame 0, subframe 0 : previous information from RU tx 0 (num_RU 1,mask 1) has not been served yet!
[MAC] [gNB 0] Frame 8 : MIB->BCH CC_id 0, Received 3 bytes
[MAC] [gNB 0] Frame 16 : MIB->BCH CC_id 0, Received 3 bytes
[MAC] [gNB 0] Frame 24 : MIB->BCH CC_id 0, Received 3 bytes
[MAC] [gNB 0] Frame 32 : MIB->BCH CC_id 0, Received 3 bytes
nrUE侧:
[HW] RX Gain 0 90.000000 (49.800000) => 40.200000 (max 76.000000)
[HW] USRP TX_GAIN:19.75 gain_range:89.75 tx_gain:70.00
[HW] Actual master clock: 46.080000MHz...
[HW] Actual clock source internal...
[HW] Actual time source internal...
[HW] RF board max packet size 1916, size for 100µs jitter 4608
[HW] rx_max_num_samps 1916
[HW] RX Channel 0
[HW] Actual RX sample rate: 46.080000MSps...
[HW] Actual RX frequency: 2.501040GHz...
[HW] Actual RX gain: 40.000000...
[HW] Actual RX bandwidth: 40.000000M...
[HW] Actual RX antenna: RX2...
[HW] TX Channel 0
[HW] Actual TX sample rate: 46.080000MSps...
[HW] Actual TX frequency: 2.501040GHz...
[HW] Actual TX gain: 19.750000...
[HW] Actual TX bandwidth: 40.000000M...
[HW] Actual TX antenna: TX/RX...
[HW] Actual TX packet size: 1916
[HW] Device timestamp: 2.359897...
[HW] [RRU] has loaded USRP B200 device.
10 Dec 16:30:55 ntpdate[13945]: adjust time server 172.19.1.64 offset 0.014141 sec
sleep...
sleep...
sleep...
sleep...
sleep...
sleep...
sleep...
sleep...
sleep...
[PHY] [SCHED][UE] Check absolute frequency DL 2501040000, UL 2501040000 (oai_exit 0, rx_num_channels 1)
[PHY] Starting sync detection
[PHY] [UE thread Synch] Running Initial Synch (mode 0)
[PHY] [UE] nr_synchro_time: Sync source = 2, Peak found at pos 305244, val = 7537049 (69 dB) avg 61 dB, ffo 0.000000
PSS execution duration 155128 microseconds
[PHY] [UE0] Initial sync : Estimated PSS position 305244, Nid2 2
[PHY] sync_pos 305244 ssb_offset 305136
[PHY] Calling sss detection (normal CP)
[PHY] [UE0] Initial sync: starting PBCH detection (rx_offset 0)
[PHY] TDD Normal prefix: CellId 881 metric 1089, phase 1, pbch -1
[PHY] [UE] nr_synchro_time: Sync source = 0, Peak found at pos 17512, val = 8553649 (69 dB) avg 61 dB, ffo 0.000000
PSS execution duration 154172 microseconds
[PHY] [UE0] Initial sync : Estimated PSS position 17512, Nid2 0
[PHY] sync_pos 17512 ssb_offset 17404
[PHY] Calling sss detection (normal CP)
[PHY] [UE0] Initial sync: starting PBCH detection (rx_offset 0)
[PHY] TDD Normal prefix: CellId 627 metric 1290, phase 5, pbch -1
[PHY] [UE0] Initial sync : Estimated power: 0 dB
[PHY] [initial_sync] trying carrier off -100 Hz, rxgain 90 (DL 2501039900, UL 2501039900)
Setting USRP TX Freq 2501039900.000000, RX Freq 2501039900.000000
[PHY] [SCHED][UE] Check absolute frequency DL 2501040000, UL 2501040000 (oai_exit 0, rx_num_channels 1)
[PHY] Starting sync detection
问题:
都是do-ra, 走射频板,UE 没有成功解码PBCH,可能是UE和GNB频率没有对应上。另外GNB侧tx-gain配置读取值为0,不太正常。GNB怎么配置tx-gain?
|
|